Aluminum 6063-T52 Rectangular Tubing, ASTM B221, 3" x 6", 0.1875" Wall, 72" Length

Aluminum 6063-T52 Rectangular Tubing, ASTM B221, 3" x 6", 0.1875" Wall, 72" Length Reviews



Other Picture


Aluminum 6063-T52 Rectangular Tubing, ASTM B221, 3" x 6", 0.1875" Wall, 72" Length Feature

  • Good resistance to general corrosion
  • Easily welded or brazed
  • Use for door and window frames, electrical components and conduit, railings and furniture, heatsinks
  • Good extrudability and high quality surface finish
  • Min 22 ksi tensile strength
Alloy 6063, one of the most popular alloys in the 6000 series, provides good extrudability and a high quality surface finish. In the heat-treated condition, alloy 6063 provides good resistance to general corrosion, including resistance to stress corrosion cracking. It is easily welded or brazed by various commercial methods (caution: direct contact by dissimilar metals can cause galvanic corrosion). Since 6063 is a heat-treatable alloy, strength in its -T6 condition can be reduced in the weld region. Selection of an appropriate filler alloy will depend on the desired weld characteristics. Consult the Material Safety Data Sheet (MSDS) for proper safety and handling precautions when using alloy 6063. Alloy 6063 offers excellent response for anodizing in its -T5, -T52 , -T53 (“matte finish”), -T54, -T6 (“lustrous” finish) tempers. The most common methods are clear, clear and color dying, and bright dipping and hard coat. Bright dipping provides an economical alternative to mechanical polished finishes while offering improved surface durability.


Visit Store Now !!

Detail Products

Detail Reviews




Oct 23, 2011 03:34:09

Zeus PTFE (Teflon) Regular Wall Tubing 11 Gauge 10' Length Spool or Coil

Zeus PTFE (Teflon) Regular Wall Tubing 11 Gauge 10' Length Spool or Coil Reviews



Other Picture


Zeus PTFE (Teflon) Regular Wall Tubing 11 Gauge 10' Length Spool or Coil Feature

  • Biocompatible USP Class VI
  • Flame Resistant UL 94 VO
  • -454 to 500 Degrees
  • Limiting Oxygen Index Greater Than 95
  • ETO and Autoclave Sterilizable
PTFE (Polytetrafluoroethylene), Sometimes referred to as Teflon is lightweight, semi flexible, and is used for a variety of laboratory applications. Heat resistant to 500 Degrees F (260 Degrees C) continuous. Highly valued for its toughness and insulating qualities, as well as high dielectric strength over a wide range of frequencies.ETO and Autoclave sterilization. Non absorbent to water and unaffected by acids and alkali's. Should not be heated to temperatures above 752 Degrees F (400 Degrees C). Color: White Translucent Natural.


Visit Store Now !!

Detail Products

Detail Reviews




Oct 19, 2011 11:40:05

Aluminum 6063-T52 Rectangular Tubing, ASTM B221, 2" x 3", 0.125" Wall, 36" Length

Aluminum 6063-T52 Rectangular Tubing, ASTM B221, 2" x 3", 0.125" Wall, 36" Length Reviews



Other Picture


Aluminum 6063-T52 Rectangular Tubing, ASTM B221, 2" x 3", 0.125" Wall, 36" Length Feature

  • Good resistance to general corrosion
  • Easily welded or brazed
  • Use for door and window frames, electrical components and conduit, railings and furniture, heatsinks
  • Good extrudability and high quality surface finish
  • Min 22 ksi tensile strength
Alloy 6063, one of the most popular alloys in the 6000 series, provides good extrudability and a high quality surface finish. In the heat-treated condition, alloy 6063 provides good resistance to general corrosion, including resistance to stress corrosion cracking. It is easily welded or brazed by various commercial methods (caution: direct contact by dissimilar metals can cause galvanic corrosion). Since 6063 is a heat-treatable alloy, strength in its -T6 condition can be reduced in the weld region. Selection of an appropriate filler alloy will depend on the desired weld characteristics. Consult the Material Safety Data Sheet (MSDS) for proper safety and handling precautions when using alloy 6063. Alloy 6063 offers excellent response for anodizing in its -T5, -T52 , -T53 (“matte finish”), -T54, -T6 (“lustrous” finish) tempers. The most common methods are clear, clear and color dying, and bright dipping and hard coat. Bright dipping provides an economical alternative to mechanical polished finishes while offering improved surface durability.


Visit Store Now !!

Detail Products

Detail Reviews




Oct 17, 2011 15:14:03

Clear Tygon 2275 High Purity Tubing, 3/16" ID, 5/16" OD, 1/16" Wall, 50' Length

Clear Tygon 2275 High Purity Tubing, 3/16" ID, 5/16" OD, 1/16" Wall, 50' Length Reviews



Other Picture


Tygon 2275 Tygon High-Purity Tubing is ideal for handling sensitive fluids such as pharmaceutical or biological solutions. There is virtually no absorption of key fluid constituents into the tubing material or fluid adsorption onto the tubing walls. As a result, fluid alteration and loss is limited. There is no plasticizer to leach into or contaminate the fluid, yet the tubing remains flexible. Tygon High-Purity Tubing can be sterilized by radiation, ethylene oxide, steam or chemical methods. Frequently, incineration is used to dispose of contaminated materials. While many tubing release hazardous by-products when burned, Tygon High-Purity Tubing only releases carbon dioxide and water when properly incinerated, providing safe disposal. Provides an uncompromising fluid path for sensitive solutions. Low sorption maintains fluid integrity. Plasticizer-free with virtually no extractable.


Visit Store Now !!

Detail Products

Detail Reviews




Oct 15, 2011 20:36:15

Clear Polycarbonate Tubing, 3/4" ID, 7/8" OD, 1/16" Wall, 72" Length

Clear Polycarbonate Tubing, 3/4" ID, 7/8" OD, 1/16" Wall, 72" Length Reviews



Other Picture


Polycarbonate is a transparent high molecular weight, linear, low-crystalline plastic. It is generally sought out for its very high impact resistance which approaches 30 times that of safety glass. Light transmittance is 90 percent. In addition to being a very hard plastic, it has a very high modulus of elasticity making it resistant to creep; it has excellent electrical resistivity, and an operating temperature range of -275 F to 250 F. It is generally unaffected by greases, oils and acids. Hardness is 112-125 Rockwell R (73-78 M Scale). Heat deflection temperature is 275-285 Degrees F at 264 PSI. Easily fabricated by machining, drilling, and sawing with a low likelihood of cracking or chipping. Solvent resistance is poor but polycarbonate is easily bonded. Prolonged exposure to solvents with the material under stress will result in crazing and cracking.


Visit Store Now !!

Detail Products

Detail Reviews




Oct 13, 2011 14:14:08

Cole Parmer White Nylon Hose Clamps, 0.750" x 0.875" 100/pk

Cole Parmer White Nylon Hose Clamps, 0.750" x 0.875" 100/pk Reviews



Other Picture


Cole Parmer White Nylon Hose Clamps, 0.750" x 0.875" 100/pk Feature

  • Cole-Parmer Nylon Hose Clamps
  • Product Type: Nominal Tubing Accessories
  • ID (min): 0.750 (19.05 mm)
  • ID (Max): 0.875 (22.2 mm)
  • Qty/pk: 100
  • Part Number: AO-06420-70
  • Package Quantity: PACKAGE
science-lab-tubing


Visit Store Now !!

Detail Products

Detail Reviews




Oct 12, 2011 06:24:04

Raychem VERSAFIT-KIT2-COL Polyolefin Heat Shrink Tubing Kit: 133 pieces per kit

Raychem VERSAFIT-KIT2-COL Polyolefin Heat Shrink Tubing Kit: 133 pieces per kit Reviews



Other Picture


Raychem VERSAFIT-KIT2-COL Polyolefin Heat Shrink Tubing Kit: 133 pieces per kit Feature

  • 2 to 1 Shrink Ratio
  • Minimum shrink temp 70 (158F)
  • Operating temperature range -55C (-67F) to 135C (275F)
Versafit polyolefin shrink tubing is highly flame retardant, very flexible, and has a low shrink temperature. It is a cost effective choice for commercial and military applications with good electrical insulation and strain relief. Easily hot stamped for identification. Each kit contains the following (6 inch pieces): 35 3/32 inch pieces, 28 1/8 inch pieces, 2:1 3/16 inch pieces, 2:1 1/4 inch pieces, 14 3/8 inch pieces and 14 1/2 inch pieces. These are split equally among the following colors: Black, Red, White, Blue, Green, Yellow, and Clear.


Visit Store Now !!

Detail Products

Detail Reviews




Oct 11, 2011 00:11:18

Zeus PTFE (Teflon) Heat Shrink Tubing, 24 Gauge, 0.006" Wall, Shrink Rat 2:1 48" Length

Zeus PTFE (Teflon) Heat Shrink Tubing, 24 Gauge, 0.006" Wall, Shrink Rat 2:1 48" Length Reviews



Other Picture


Zeus PTFE (Teflon) Heat Shrink Tubing, 24 Gauge, 0.006" Wall, Shrink Rat 2:1 48" Length Feature

  • Tensile Strength 2,500 to 4,000 psi
  • Maximum continuous operating temp. 500 F
  • Excellent Chemical Resistance
  • Clear View
  • Lubricious Finish
This PTFE Heat Shrink 2:1 Tubing has a shrink range of 650 F +/- 25 F (343 C +/-10 C). PTFE (Polytetrafluoroethylene) goes into the gel state (amorphous to crystalline) at approximately 625 F (330 C). PTFE begins to shrink at 650 F (343 C). The mandrel or part to be covered by the Heat shrink tubing must be able to withstand this temperature range. Color: Clear.


Visit Store Now !!

Detail Products

Detail Reviews




Oct 08, 2011 00:30:05

Aluminum 6061-T6511 Round Tubing, 1.5" OD, 1.124" ID, 0.188" Wall, 36" Length

Aluminum 6061-T6511 Round Tubing, 1.5" OD, 1.124" ID, 0.188" Wall, 36" Length Reviews



Other Picture


Aluminum 6061-T6511 Round Tubing, 1.5" OD, 1.124" ID, 0.188" Wall, 36" Length Feature

  • Excellent corrosion resistance
  • Versatile for medium to high strength requirements
  • Use for transportation components, recreation products, machinery and equipment
  • Good finishing characteristics
  • Min 38 ksi tensile strength
Aluminum 6061 is one of the most widely used alloys in the 6000 series. This standard structural alloy, one of the most versatile of the heat-treatable alloys, is popular for medium to high strength requirements and has good toughness characteristics. Alloy 6061 has excellent corrosion resistance to atmospheric conditions and good corrosion resistance to seawater. This alloy also offers good finishing characteristics and responds well to anodizing; however, where cosmetic appearance is critical, consider the use of alloy 6063. For screw machine applications, alloy 6061 has adequate machinability characteristics in the heat-treated -T6/-T6511 condition. Chips from machining (particularly turning and drilling) can be difficult to break in the -T6/-T6511 temper condition. Chip breakers are recommended, and special machining techniques (i.e. peck drilling) can improve chip formation.


Visit Store Now !!

Detail Products

Detail Reviews




Oct 05, 2011 03:59:14

Masterflex , C-FLEX (50 A), L/S 18, 25 ft.

Masterflex , C-FLEX (50 A), L/S 18, 25 ft. Reviews



Other Picture


Masterflex , C-FLEX (50 A), L/S 18, 25 ft. Feature

  • Precision C-Flex (50 A) Tubing
  • Combines biocompatibility of silicone with chemical resistance similar to Tygon
  • Very low protein binding
  • Heat sealable, weldable
  • Economical tubing
  • Product Type: Masterflex L/S Tubing
  • Pump Series: L/S
  • Tubing formulation: C-Flex
  • Sterilization Method: Autoclave, Ethylene Oxide, Gamma Irradiation
  • Min temperature (° F): -100
  • Min temperature (° C): -73
  • Max temperature (° F): 275
  • Max temperature (° C): 135
  • Masterflex tubing size (L/S): 18
  • Tubing ID (mm): 9.5
  • Tubing ID (inches): 0.31
  • Hose barb size (inches): 0.375
  • Resin certification (FDA): Yes
  • Resin certification (European Pharmacopoeia): Yes
  • Resin certification (USP): Yes
  • Length per pack (m): 7.6
  • Length per pack (ft): 25
  • Max vacuum (" Hg): 20
  • Max vacuum (mm Hg): 510
  • Flow range with 6 to 600 rpm drive (ml/min): 23 to 2300
  • Max pressure (psi): 15
  • Max pressure (bar): 1.035
  • Max pressure continuous (psi): 15
  • Max pressure continuous (bar): 1.0
  • Suction lift (ft H2O): 22
science-lab-tubing


Visit Store Now !!

Detail Products

Detail Reviews




Oct 03, 2011 20:20:04

Zeus FEP Heat Shrink Tubing, 1 Gauge, 0.0 12" Wall, Heat Shrink Rat 1.13:1 48" Length

Zeus FEP Heat Shrink Tubing, 1 Gauge, 0.0 12" Wall, Heat Shrink Rat 1.13:1 48" Length Reviews



Other Picture


Zeus FEP Heat Shrink Tubing, 1 Gauge, 0.0 12" Wall, Heat Shrink Rat 1.13:1 48" Length Feature

  • Tensile Strength, psi at 73 Deg F 3,000 - 4,000
  • Elongation at 73 Deg F .300 percent
  • Specific Gravity 2.12 - 2.17
  • Shrink ratio is 1.3 to 1
  • Maximum continuous operating temp. 500 F
This heat shrinkable FEP (Fluorinated Ethylene-Propylene) Tubing will shrink rapidly over inserted objects upon exposure to moderate heat. Soldered joints, parts, components and fittings of plastic, metal or wood that could not previously be protected because of the high temperature required for shrinkage can now have a transparent surface of Teflon with a continuous service temperature of 400 F (204 C). Shrinkage will occur completely at exposure to 350 F (177 C) with partial shrinkage beginning as low as 200 F (93 C). Suggested for connecting metal, glass or plastic tubes of similar or dissimilar diameters in low pressure applications. FEPs chemical resistance and dielectric properties are equal to PTFE (Polytetrafluoroethylene).


Visit Store Now !!

Detail Products

Detail Reviews




Oct 02, 2011 23:20:04

Aluminum 6061-T6511 Round Tubing, 1" OD, 0.87" ID, 0.065" Wall, 36" Length

Aluminum 6061-T6511 Round Tubing, 1" OD, 0.87" ID, 0.065" Wall, 36" Length Reviews



Other Picture


Aluminum 6061-T6511 Round Tubing, 1" OD, 0.87" ID, 0.065" Wall, 36" Length Feature

  • Excellent corrosion resistance
  • Versatile for medium to high strength requirements
  • Use for transportation components, recreation products, machinery and equipment
  • Good finishing characteristics
  • Min 38 ksi tensile strength
Aluminum 6061 is one of the most widely used alloys in the 6000 series. This standard structural alloy, one of the most versatile of the heat-treatable alloys, is popular for medium to high strength requirements and has good toughness characteristics. Alloy 6061 has excellent corrosion resistance to atmospheric conditions and good corrosion resistance to seawater. This alloy also offers good finishing characteristics and responds well to anodizing; however, where cosmetic appearance is critical, consider the use of alloy 6063. For screw machine applications, alloy 6061 has adequate machinability characteristics in the heat-treated -T6/-T6511 condition. Chips from machining (particularly turning and drilling) can be difficult to break in the -T6/-T6511 temper condition. Chip breakers are recommended, and special machining techniques (i.e. peck drilling) can improve chip formation.


Visit Store Now !!

Detail Products

Detail Reviews




Oct 01, 2011 22:42:04